Project case study · Kemah, TX

A Single Gate Installation for Ramsey Horton in Kemah, TX

Ramsey already owned the gate for his Kemah entrance; he needed it measured, set plumb in concrete and fitted with a working handle. Here is how Mustang installed it, and why gate hardware near Galveston Bay needs more corrosion resistance than hardware built for an inland site.

  • Reviewed Nov 3, 2026
  • Source: American Galvanizers Association
  • 3 job photos
Ornamental iron gate set into a brick wall
The finished gate set into the brick wall at Ramsey’s Kemah entrance.
The short answer

Mustang Fencing installed a single gate Ramsey Horton already owned at his home in Kemah, TX. The posts were measured and marked for alignment with the existing layout, set plumb and level, and anchored with two bags of concrete each. A door handle was attached once the concrete set, and the hinges were tested before the job was finished.

Single gateRamsey’s own gate, professionally installed
2 bags of concretePer post, for a stable footing
Plumb and levelPosts set before the pour
Kemah, TXDoor handle attached and tested

Sources: this project’s own documented facts; American Galvanizers Association, HDG Corrosion Rates for ISO Categories C1-C5/X. Checked November 3, 2026.

The job: installing Ramsey’s own gate

Ramsey Horton already had a gate for the entrance to his Kemah home; he needed it professionally installed, with security and functionality in mind. Mustang Fencing measured and marked the gate’s placement to keep it aligned and symmetrical with the existing property layout, then prepared the ground for the posts.

The posts were positioned and checked for plumb and level before the concrete was poured — two bags per post — to give the gate a stable base. Once the concrete set, a door handle was attached and aligned, the hinges were tested for smooth operation, and the site was cleaned up.

Two panels. Left: posts measured, marked and leveled plumb, then two bags of concrete poured per post. Right: a door handle attached once the concrete set, hinges tested, and the area cleaned up. The documented installation sequence STEP 1: MEASURE, SET & POUR Measured, marked, leveled plumb then 2 bags of concrete poured per post STEP 2: HANDLE, TEST & CLEAN UP Door handle attached once concrete set Hinges tested, area cleaned From this project’s own documented facts (post content + photos). Not an external source.
S-1
DrawingThe documented installation sequence
BasisPublished job facts (post content + photos)
ScaleNot to scale
The sequence this project’s own documentation shows: posts measured and set first, hardware and testing last.
Installer holding boxed gate hardware beside a metal gate
Gate hardware staged before installation at Ramsey’s home.

Why gate hardware near Galveston Bay needs extra corrosion resistance

Kemah sits directly on Galveston Bay, which puts any outdoor metal hardware in a marine air environment. The American Galvanizers Association’s published corrosion model tracks how fast a standard zinc coating wears away in different environments — and coastal, salt-laden air corrodes zinc noticeably faster than inland rural or suburban air. That is the real reason durable, corrosion-resistant hardware matters more on a Kemah gate than it would on the same gate built fifty miles inland.

Two panels comparing average zinc corrosion rates. Left: inland rural or suburban air, about 0.75 to 1.00 micrometers of zinc lost per year. Right: coastal temperate or tropical marine air, about 1.15 to 1.26 micrometers lost per year, roughly 50 percent faster, noting that Kemah sits on Galveston Bay. Inland vs. coastal: how much faster zinc corrodes near the water INLAND (RURAL / SUBURBAN) 0.75–1.00 µm zinc loss / year COASTAL (TEMPERATE / TROPICAL MARINE) 1.15–1.26 µm zinc loss / year Kemah sits on Galveston Bay American Galvanizers Association Time-to-First-Maintenance model: average zinc corrosion rate by environment. Coastal marine air corrodes roughly 50% faster than rural/suburban inland air.
S-2
DrawingInland vs. coastal: how much faster zinc corrodes near the water
BasisAmerican Galvanizers Association, HDG Corrosion Rates for ISO Categories C1-C5/X (Time-to-First-Maintenance model)
ScaleNot to scale
Zinc-coated hardware corrodes meaningfully faster in Kemah’s coastal air than it would inland.

Gate-post concrete calculator

A geometry-based estimate of how much concrete a single round post hole needs, assuming a square post set for the full hole depth. Not a measurement of Ramsey’s own posts, and not a substitute for a site-specific check — convert to bags using the yield printed on your concrete bag.

0CUBIC FT OF CONCRETE

Volume = (cylinder volume of the hole) − (volume of the post over that depth), converted from cubic inches to cubic feet (÷ 1728). Check your bag’s packaging for its cubic-foot yield to convert this to a bag count.

Metal gate frame being fitted against a brick wall
Fitting the gate frame against the brick wall at the entrance.
★★★★★
We just installed iron gate and it looks amazing thank you very much mustang fencing .
Jordan Carrillo · Google review · a year ago
★★★★★
Mustang’s team installed iron fence for me and did an absolutely incredible job! I would recommend this company to anyone I know!
Theodore Howitt · Google review · a year ago
★★★★★
Very professional and friendly. Gotten automatic gates done and they are done to perfection! Thank you
Tannia Cravinas · Google review · a year ago

Reviews shown word for word from the Mustang Fencing Services Google Business Profile (Galveston), captured 2026-11-02.

Questions we get about this

What did Mustang Fencing install for Ramsey Horton?
A single gate Ramsey already owned, at his home in Kemah, TX. Mustang measured and set the posts, poured two bags of concrete per post, and attached and tested a door handle.
Why does the gate hardware need to resist corrosion?
Kemah sits on Galveston Bay, and the American Galvanizers Association’s published data shows zinc-coated hardware corrodes meaningfully faster in coastal marine air than it does inland — roughly 50% faster by their model.
How was the gate anchored?
The posts were measured, marked for alignment with the existing layout, set plumb and level, and anchored with two bags of concrete per post.
Was the gate itself new?
No — Ramsey already had the gate. The job was a professional installation: posts, concrete, alignment, the door handle and hinge testing.
Does Mustang Fencing serve Kemah, TX?
Yes. See fence and gate installation in Kemah for the area served.

Sources

Checked November 3, 2026. Rules change, so confirm with the City before you build.

  1. American Galvanizers Association, HDG Corrosion Rates for ISO Categories C1-C5/X — Time-to-First-Maintenance model giving average zinc corrosion rates by environment (rural, suburban, temperate marine, tropical marine), used here to explain why coastal gate hardware needs more corrosion resistance than inland hardware.
Free on-site estimate

Need a gate installed or reinforced near the water?

We’ll check post placement, concrete footing and hardware before any order goes on a written estimate.

Page reviewed November 3, 2026 by Mustang Fencing Services, Galveston. Next review due May 2027.