Project case study · Baytown, TX

A Double-Doored, Arched 4×6 Wood Drive Gate for Anthony Rice in Baytown, TX

Anthony Rice wanted a driveway gate that was sturdy, secure, and made a statement — a double-doored, arched 4×6 wood drive-in gate. Here is what Mustang documented about the build: premium wood, heavy-duty hinges and a locking mechanism, a sloped driveway accounted for so both doors swing clear, plus why exterior wood gates near Galveston Bay are installed to the same moisture target used across most of the country.

  • Reviewed Nov 8, 2026
  • Source: USDA Forest Products Laboratory Wood Handbook
  • 1 job photo
Arched double wood gate closing off a concrete driveway
Anthony Rice’s finished double-doored, arched 4×6 wood drive-in gate in Baytown, TX.
The short answer

Mustang Fencing built a double-doored, arched, 4×6 wood drive-in gate for Anthony Rice in Baytown, TX, with heavy-duty hinges and a locking mechanism, accounting for a slight slope in the driveway so both doors swing clear.

4 ft × 6 ftEach gate leaf (per the job title)
2 leavesDouble-doored, arched top rail
9%–14%USDA target install moisture range, exterior wood
Baytown, TXGulf Coast humidity exposure

Sources: this project’s own documented facts and photo; USDA Forest Products Laboratory, Wood Handbook: Wood as an Engineering Material (FPL-GTR-282, 2021). Checked November 8, 2026.

The job: a double-doored, arched drive gate built to spec

Anthony Rice wanted more than a functional driveway gate. He asked for a double-doored, arched, 4×6 drive-in gate — wide enough for vehicle access, with an arched top rail to match his home’s architecture, and built from premium wood to hold up to Baytown’s weather.

Mustang’s team removed the old gate, anchored new posts, and built the gate with heavy-duty hinges and a locking mechanism at the center meeting rail where the two leaves close together.

Diagram of a double-doored arched wood drive gate with two leaves, an arched top rail, heavy-duty hinges on each leaf, and a locking mechanism at the center meeting post THE DOCUMENTED GATE: A DOUBLE-DOORED, ARCHED, 4×6 WOOD DRIVE-IN GATE ARCHED TOP RAIL, SPANS BOTH LEAVES LEAF 1 CENTER MEETING POST WITH LOCKING MECHANISM LEAF 2 6 FT LEAF HEIGHT 4 FT PER LEAF (DOCUMENTED SIZE)
S-1
DrawingThe documented gate: double-doored, arched, 4×6
BasisThis project’s own documented facts and photo
ScaleNot to scale
Not a build plan — exact hardware placement on Anthony’s gate isn’t documented. What is documented: two leaves, an arched top rail, heavy-duty hinges, and a center locking mechanism.

Handling the uneven terrain around the driveway

The driveway itself wasn’t perfectly flat. Mustang’s team found uneven terrain around the opening, with a slight slope across the width of the gate. Hanging both leaves level while keeping a consistent gap at the bottom took careful adjustment during installation.

The result: both doors open and close without dragging on the high side of the driveway, even though the grade underneath isn’t dead level.

Diagram of a sloped driveway with two gate leaves whose bottom rails are cut to follow the grade, keeping a constant clearance gap on both leaves ACCOUNTING FOR THE SLOPE: BOTTOM CLEARANCE ACROSS AN UNEVEN DRIVEWAY DRIVEWAY GRADE — SLIGHT SLOPE, LEFT TO RIGHT BOTTOM RAIL CUT TO FOLLOW THE GRADE, CONSTANT GAP BOTH LEAVES (so both doors swing clear without dragging on the high side)
S-2
DrawingAccounting for the slope
BasisThis project’s own documented facts
ScaleNot to scale
Illustrative, not a survey of Anthony’s actual grade. What’s documented: the driveway had a slight slope, and the installed gate operates without issues across it.

Why a wood drive gate near Galveston Bay is built to a specific moisture target

Wood gates move with humidity. The USDA Forest Products Laboratory’s Wood Handbook publishes recommended moisture-content targets for exterior wood at the time of installation, broken out by climate region. For “most areas of the United States,” the average target is 12%, with individual pieces ranging 9%-14%.

Here’s the part that surprises people: the “damp, warm coastal” column — the one Baytown falls into — carries the same 12% average and 9%-14% range as most of the country for exterior wood. It’s the dry Southwest that’s the outlier, targeting a drier 9% average so lumber doesn’t swell too much after it picks up ambient humidity. A gate built near Galveston Bay isn’t installed any wetter or drier than one built almost anywhere else in the U.S. — it just can’t be installed outside that 9%-14% band without risking a bind or a gap at the arch reveal where the two leaves meet.

Bar chart comparing recommended exterior wood installation moisture content for most U.S. areas, the dry Southwest, and damp warm coastal areas including Baytown, Texas EXTERIOR WOOD TARGET MOISTURE CONTENT AT INSTALL (USDA WOOD HANDBOOK, TABLE 13-2) 16%8%0% 12% AVG MOST U.S. AREAS 9% AVG DRY SOUTHWEST 12% AVG DAMP COASTAL (BAYTOWN)
S-3
DrawingExterior wood target moisture content at install
BasisUSDA Forest Products Laboratory, Wood Handbook (2021), Table 13-2
ScaleNot to scale
Baytown’s own climate column matches the national default band for exterior wood (12% average, 9%-14% range). The dry Southwest is the one that differs.

Why wood species also matters at a tight arch reveal

Moisture-content target is only half the picture — how much a given board actually moves per percentage point of moisture change depends on the species. The Wood Handbook‘s Table 13-5 publishes a dimensional-change coefficient for each species. Across a published, hypothetical 5-point moisture swing (for example, from 9% up to 14%), a 6-inch board of Eastern redcedar widens by roughly 0.05 in, while the same board in Southern yellow pine widens by roughly 0.08 in — about 60% more movement for the same swing.

Anthony’s gate is documented only as “premium wood,” not a named species, so the figures below are reference points from the USDA table, not a claim about what his gate is built from. The practical takeaway for any double-doored arched gate: the tighter the reveal where the two leaves meet, the more species and curing matter.

Diagram comparing swelling of a 6 inch wide board of Eastern redcedar versus Southern yellow pine across a 9 to 14 percent moisture content swing, using USDA published dimensional change coefficients WHY SPECIES MATTERS: SWELLING ACROSS A 9% TO 14% MOISTURE SWING, 6 IN BOARD EASTERN REDCEDAR CT = 0.00162 (USDA Table 13-5) 6 in + ~0.05 in (about 1/16 in) SOUTHERN YELLOW PINE CT = 0.00259 (USDA Table 13-5) 6 in + ~0.08 in (about 5/64 in)
S-4
DrawingWhy species matters at a tight reveal
BasisUSDA Forest Products Laboratory, Wood Handbook (2021), Table 13-5
ScaleNot to scale
Reference species only — not a claim about which wood is in Anthony’s gate.

Wood board swelling calculator

Straight arithmetic from USDA’s published dimensional-change coefficients (Table 13-5). Not a spec for Anthony’s gate — its exact wood species isn’t documented.

USDA Forest Products Laboratory, Wood Handbook (2021), Table 13-5: width change = width x CT x moisture-content change, tangential direction.

★★★★★
Very professional and friendly. Gotten automatic gates done and they are done to perfection! Thank you
Tannia Cravinas · Google review · a year ago
★★★★★
I have hired Mustang fencing services to fix my backyard fencing. Good wood to used. I really like theirs work. Best of luck
Zaidbin Saif · Google review · a year ago
★★★★★
Amazing work will go ahead and recommend everyone in friends and family We installed 8ft tall double sided stained cedar wood fence in our backyard, it’s really looks great, installed perfectly nice finishing and cost effective, thanks mustang fencing.
Muqeet Mohammed Abdul · Google review · a year ago

Reviews shown word for word from the Mustang Fencing Services Google Business Profile (Galveston), captured 2026-11-08.

Questions we get about this

What did Mustang Fencing build for Anthony Rice?

A double-doored, arched, 4×6 wood drive-in gate in Baytown, TX, with heavy-duty hinges and a locking mechanism at the center meeting rail.

Why does the gate have an arched top rail?

Anthony asked for an arched design to match his home’s architecture while still giving a wide enough opening for vehicle access.

How did Mustang handle the sloped driveway?

The team found uneven terrain and a slight slope at the opening, and adjusted the installation so both leaves keep a consistent bottom clearance and swing without dragging.

Does a coastal location change how a wood gate should be installed?

Less than you might expect. USDA’s Wood Handbook puts “damp, warm coastal” areas like Baytown in the same 9%-14% exterior wood moisture-content band used for most of the U.S. It’s the dry Southwest that targets a noticeably drier installation.

Does Mustang Fencing build custom drive gates elsewhere near Galveston?

Sources

Checked November 8, 2026. Rules change, so confirm with the City before you build.

  1. USDA Forest Products Laboratory, Wood Handbook: Wood as an Engineering Material (FPL-GTR-282, 2021) — Table 13-2 recommended moisture content at installation for exterior wood, by U.S. climate region; Table 13-5 dimensional-change coefficients by species.
Free on-site estimate

Planning a double-doored or arched drive gate near Baytown or Galveston Bay?

We’ll walk the driveway with you — including any slope or uneven ground — before any written estimate.

Page reviewed November 8, 2026 by Mustang Fencing Services, Galveston. Next review due May 2027.